Summary

Our Score

6/10

Review Price free/subscription

Sapphire PC-AM2RX780 - Sapphire PC-AM2RX780

Running the Sapphire gave us a series of small but annoying problems. For starters there was the Sapphire power supply issue that has cropped up a few times in the past. For motherboard testing we use either an Enermax Galaxy 850Wor CoolerMaster 850W power supply as they have plenty of connectors to feed modern graphics cards. Small Sapphire motherboards are incompatible with these PSUs as, apparently, the PSUs are divided up internally in a way that confuses the motherboard with the result that the board appears to be dead. For Sapphire testing we have to resort to an old Antec Neo 480W with an adapter to supply the six-pin graphics.

Then we had to get to grips with the BIOS on the PC2-AM2RX780 which is quite familiar yet it behaves in a slightly odd fashion. When you make a change it is unlikely to take effect instantly as the board often fails to restart. You make a change, save and restart, cross your fingers and hope that Windows comes to life. If it doesn't start you have to hit the power switch and then start the system from cold. If Windows starts this time then all is well but if not you have to disconnect the power connectors and clear the CMOS. It's a pain in the neck and took us round in circles a number of times until we found settings that worked successfully.
/94/0dd715/763b/7480-angle2.jpg
Also, we were using 64-bit Windows Vista which refused to run the installer on the Sapphire driver CD as the software wasn't digitally signed.

The default CPU voltage when Cool ‘n' Quiet is disabled is 1.34V and as we found that supplying as much as 1.475V made no difference to the overclocking of this particular CPU we set the voltage manually to 1.35V to avoid any uncertainty.

Overclocking our Phenom X4 9750 gave a relatively small improvement in performance but once the processor speed was raised from 2.4GHz to 2.64GHz the graphics performance took a hit.

There's something a bit odd about the memory support on the PC2-AM2RX780 as the packaging refers to DDR2 800MHz support yet the manual refers to support for 1,066MHz memory. There's a setting in the BIOS to increase the default speed of 800MHz to 1,066MHz and Phenom supports this faster speed so it would seem that there is a simple misprint on the packaging.
/94/b8ef9c/4f3b/7480-box.jpg
In practice we found the answer was a little more subtle than that. Once the RAM voltage was increased in the BIOS to 2.1V, to give our Corsair memory enough power to run at 1,066MHz, the system refused to play ball. We had been able to increase the 200MHz clock speed to 220MHz with the memory running at 800MHz but when the memory speed was increased to 1,066MHz the system locked solid. After a couple of resets we dropped the clock to 210MHz and the faster memory speed worked properly. Eventually we came to the conclusion you can either have a more overclocked Phenom with 800MHz memory or you can sacrifice a bit of CPU speed to run your memory a bit faster as well.

The upshot was that the Phenom ran stably at a slightly overclocked speed but the amount of messing around was far too much like hard work. Although our experiences with the B3 Phenom were more successful than the original B2 it is still far from perfect. In fact, the only one of the Phenom X4 range we can wholeheartedly recommend you try is the multiplier unlocked 9850 Black Edition as this gives you a guaranteed good overclock and costs little more than the alternatives.

As for the Sapphire PC2-AM2RX780, it is a perfectly mediocre board that uses a chipset we have little reasons to enthuse about. By all means go for a 780G motherboard but a 770 with CrossFire holds little appeal.

Verdict

There's little to make the Sapphire AM2RX780 stand out from the crowd and with an iffy BIOS as well it's even less of an attractive proposition. Combined with the limited appeal of siding with AMD and its Phenom range anyway, this is probably one to avoid.

Previous page
Next page
comments powered by Disqus